Type: Driver
File Name:
File Size: 32.3 MB
13 (3.73)
Downloads: 8
Supported systems: Windows 10, 8.1, 8, 7, 2008, Vista, 2003, XP, Other
Price: Free* (*Free Registration Required)

Download Now


From Bitwise Systems. The chip is a Cypress CY7C Reserved for future use Bit 1: Active high signal Bit 0: Active high signal.

Reserved Do not change Bit 0: Description Configures Port C default state. Writing a register bit to IOC writes to the port pin latch. Configures Port D default state. Writing a Bitwise QuickUSB Module bit to IOD writes to the port pin latch. Configures Port E default state.

  • Drivers for QuickUSB QUSB2 Module
  • Kanda Shop - Manufacturer is BitwiseSystems
  • Architecture and Implementation of OpenPET Firmware and Embedded Software
  • QuickUSB driver for Linux
  • QuickUSB User Guide v2.11.41
  • Architecture and Implementation of OpenPET Firmware and Embedded Software

Writing a register bit to IOE writes to the Bitwise QuickUSB Module pin latch. Unused Bit 9: INT1 is not currently used Bit 8: Reserved for future use. A WORD containing the setting address.

A WORD containing the new setting value. The defaults are non-volatile and are read into the settings table on power up.

Plug-in module adds USB 2.0 to designs

If you are configuring multiple devices, they must be daisy-chained and the configuration Bitwise QuickUSB Module combined in the conversion process into a single binary file. To configure an FPGA, follow these steps: This resets the FPGA and starts the configuration process. Repeat this process until the entire file is sent.

Of course, the last block will probably be less than the maximum block size. In addition, if you need to restart the configuration process for some reason, you can call restart at step 1 at any time.

Be sure to close the binary FPGA configuration file when you are done. Learn more about Amazon Prime. Back to top.

Get to Know Us. Ideal Bitwise QuickUSB Module labs, observatories, research institutes and products where fast data transfer is essential. The target interface consists of: Greenjak jampro50 Search within store. Visit Store: Greenjak Stock G Shipping and handling. This item will ship to Ukrainebut the seller has not specified shipping options.

QuickUSB User Guide

Contact the seller - opens in a new window or tab and request a shipping method to your location. Shipping cost cannot be calculated. You can add your email to this OpenPET Bitwise QuickUSB Module list by sending a message to sympa lists. Aug 8 9: After you have successfully installed the correct firmware, you can confirm your installation by running the QuickUsb Diagnostics see Fig. Even if you only plan to use the off the shelf OpenPET software and firmware, the OpenPET system requires the use of Altera design tools in order to load the appropriate firmware into the Bitwise QuickUSB Module Board. These tools can be downloaded for free from the Altera Download Center website e. You can select additional options such as the ModelSim-Altera Edition simulation toolsbut they are not required to run OpenPET and they will lengthen the download time.

Download and install Bitwise Systems QuickUSB QUSB2 Module Unprogrammed - driver id

You are then required to log Bitwise QuickUSB Module with your username and password if you already have a myAltera account. If not, then create an account using your email address and complete the account registration information. Once your myAltera account has been created, you will be directed to your myAltera Home page. Select the Download Center link on the top right side of the page. Once you have returned to the Download Center Fig. Plug QuickUSB into Altera Development Kits with a Santa Cruz port. Includes all the hardware you need to plug your QuickUSB® Plug-In module into your board. The Easy-to-Use Hi-Speed USB Module. The quickest way to add high-speed USB to your product is with QuickUSB®. Since all the USB functionality is in.

Other Drivers