AGILENT 34945A DRIVER FOR WINDOWS DOWNLOAD
AGILENT 34945A DRIVER DETAILS:
|File Size:||7.4 MB|
|Supported systems:||Windows 10, Windows 8.1, Windows 7|
|Price:||Free* (*Free Registration Required)|
AGILENT 34945A DRIVER
Keysight Technologies (formerly Agilent) EXT Extender board for KTA (Used)
They only Agilent 34945A the relay coil, so position feedback and LED drivers must be provided by additional Digital Input and Output hardware. Add this to the complexity Agilent 34945A power distribution, and you end up with an expensive solution that is also difficult to troubleshoot when failures occur. This section will show you how to select options for Agilent switches and attenuators to configure the most efficient and easy-to-use system. Here are the recommended attributes: In many cases, you actually pay more for 12 V or 5 V coils. Selecting 24 V relay coils simplifies this process and permits you to drive switches without an external power supply when connecting to the first EXT module. Position feedback is often a standard feature with Agilent switches, because the construction of the switch drive signals can also feed back informationabout the state of the switch.
D-sub socket connectors allow for the easiest connection to Yx distribution boards. Here are a few that are Agilent 34945A of comment: However, this option usually adds cost to the switch, and it forces all switches connected to the Yx to use the same drive mode.
Solder lugs may appear to be cheaper with some switches, but you should consider the labor costs Agilent 34945A reliability. In many cases, the standard configuration of the switch is a D-sub connector, so you may actually pay more for solder lugs. And, finally, current interrupts almost always add cost to the switch.
They allow you to apply a constant voltage to a switch, and the switch actuates to create its own pulsed mode to change states. Current interrupts do offer the fastest programming time, because the switch actuates as fast as Agilent 34945A can rather than the timed response of a pulse-mode control circuit. It is the EXT that actually performs all the control and Agilent 34945A operations.
Agilent 34945A Microwave Switch/Attenuator Driver for 34980A
Each EXT can drive up to 64 coils, where each of four Yx boards route the control of relay coils, the position feedback, and the drive for external LEDs for up to 16 coils. Some devices require two or more coils and provide varying ways of indicating position feedback. The Yx boards handle all of those signals for you. You need only provide a simple ribbon cable with standard socket connectors. The image on the following page shows a Agilent 34945A of the YA Distribution board.
HP - Agilent - Keysight 34945A in Farmingdale, NJ, USA
Each LED socket header represents the state of up to eight coils, and each vertical lead-pair connects to the LED, representing the section position. You can route a ribbon cable with a pin connector up to your control panel viewing area. Relay control and Agilent 34945A feedback is provided in either a socket header or with screw terminals for the YA. Most of the Yx boards have socket headers for easy connection to Agilent switches and Agilent 34945A. Pulse drive, coil voltage, position feedback, bandwidth, connectors, and termination represent a complex set of options in selecting any switch.
Agilent 34945A However, this process is made easier by first matching switches and attenuators with the correct Yx distribution board. First, find the Agilent switch or attenuator required Agilent 34945A the leftmost columns in Table 1 and Table 2. Adjacent columns show the recommended options for the relays.
If these relays and options are ordered, Agilent 34945A construction, indicator read back and power becomes very simple. A If the relays required for your design can be procured with the recommended options, cable construction and system configuration becomes very simple. Follow these steps below: Relay control and position feedback 2.
Next, notice that the rightmost columns specify which distribution board to use and how many of the switches or attenuators are supported on each board. Agilent 34945A that some boards support multiple devices. Finally, once you know which distribution board s to use, refer to specific distribution card table for details on the associated distribution boards s.
|QNAP TVS-EC1280U-SAS-RP TurboNAS QTS||Need Help with this product?|
|A4Tech RK(S)-2370D||Agilent/Hp 34945A Switch / Attenuator Driver For 34980A Mainframe (Ref:552)|
|Gateway GM5052e ATI Theater 550 PRO TV Tuner||RF/Microwave Switching Solutions|
|ASUS N75SF ASMedia USB 3.0||Microwave switch/attenuator driver for KT-34980A/DMM|
|Sony Xperia Z1 (SO-02F) USB||Keysight (Agilent) E5062A ENA-L RF Network Analyzer, 300 kHz – 3 GHz|
The Keysight A switch/attenuator driver module for the A Multifunction Switch/Measure Unit allows you to control Agilent 34945A and attenuators external. EXT Extender board for A and LA, one required for each 64 coils.